Darkfield using Olympus BH2/BHS

Here you can discuss different microscopic techniques and illumination methods, such as Brightfield, Darkfield, Phase Contrast, DIC, Oblique illumination, etc.
Post Reply
Message
Author
sombre
Posts: 11
Joined: Mon Jul 30, 2018 8:14 am

Darkfield using Olympus BH2/BHS

#1 Post by sombre » Wed May 22, 2019 6:07 pm

Assistance please,
My microscope is an Olympus bh2/bhs and i should like to be able to view subjects in darkfield.
Unfortunately there is no filter holder beneath the condenser in which to place a darkfield patch stop.
Does anyone know a way in which i can work round this problem, or if there is an attachment or
alternative condenser i could get. If so please let me know.
I have spent countless hours searching the net for some kind of fix, but to no avail, I would therefore be most grateful for
any advice.

Many thanks,
Sombre

User avatar
admin
Site Admin
Posts: 49
Joined: Sat Oct 11, 2014 9:22 am

Re: Darkfield using Olympus BH2/BHS

#2 Post by admin » Wed May 22, 2019 7:50 pm

Hello,

1. Check if the condenser has a push on filter holder (and not a swing out type). The filter holder sometimes contains a blue glass filter. The patch stop goes on top of the blue glass.
2. If you do not have a filter holder at all, then make yourself a patch stop using overhead foil. Tape it there where the filter holder should go.

What about these:
https://www.ebay.com/itm/Olympus-1-25-N ... SwhzhcUi4h
https://www.ebay.com/itm/Olympus-CH-Mic ... SwqURatO8G
https://www.ebay.com/itm/Olympus-1-25-M ... SwFZtbRmLH

Maybe this one also fits, becasue it has 37mm:

https://www.ebay.com/itm/Biological-Mic ... 0005.m1851

Oliver
Science may set limits to knowledge, but should not set limits to imagination.
(Bertrand Russell)

PrecisionInstruments
Posts: 14
Joined: Mon May 06, 2019 11:44 am
Location: Perth, Western Australia

Re: Darkfield using Olympus BH2/BHS

#3 Post by PrecisionInstruments » Thu May 23, 2019 12:09 pm

The BH2 (BHT, BHTU, BHS) had either a dedicated Darkfeild condenser, or a dark field ring incorporated in the phase condenser turret. These would fit into the position where your current condenser is. I believe the condensers in the links or above post would not be compatible with your microscope.
I have a headache, For which the future’s made

Hobbyst46
Posts: 2191
Joined: Mon Aug 21, 2017 9:02 pm

Re: Darkfield using Olympus BH2/BHS

#4 Post by Hobbyst46 » Thu May 23, 2019 12:35 pm

A dedicated darkfield and/or phase contrast condenser is best, yet sometimes expensive and rare. A phase condenser offers more options and is preferrable IMO. Although it does not give DF with objectives of NA>1.

A year ago I faced a similar problem. Black patch circles, like Rhinebergs and black arrows failed to give DF on my scope. So I DIY'd two LED ring substitutes.

An adventure. Here is the link.
viewtopic.php?t=5876
There are two gadgets: LED ring and LED strip. The latter is harder to make and, for me, was not as satisfactory. So I would start with the former. Both were inspired by scientific articles...
Zeiss Standard GFL+Canon EOS-M10, Olympus VMZ stereo

sombre
Posts: 11
Joined: Mon Jul 30, 2018 8:14 am

Re: Darkfield using Olympus BH2/BHS

#5 Post by sombre » Fri May 24, 2019 9:36 am

Many thanks to all for the help and suggestions.
I think I will go down the diy route until such times as I can find the correct condenser etc:
Again many thanks.

Sombre

Crusty
Posts: 35
Joined: Fri Mar 17, 2017 4:19 pm

Re: Darkfield using Olympus BH2/BHS

#6 Post by Crusty » Wed Jun 05, 2019 10:00 pm

I just purchased this everything (oblique, darkfield, polarizing, Rheinberg) kit specifically for BH2's. I've only been playing with it for a few days, but I'd delighted with it.

https://www.ebay.com/itm/Olympus-micros ... 2749.l2649

Post Reply