Man made?
Man made?
Found this in a freshwater sample. Holes are 12µm diameter
- Attachments
-
- 12µm diameter.jpg (98.7 KiB) Viewed 5511 times
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)
Re: Man made?
Sure looks like it. Perhaps part of a filter (oil, air, water, . . .) ??
Might be part of something like a micro-perforated bag (used for bread etc.)?? Not quite the same look, though.
It also seems that bits of plastic are showing up everywhere in nature. If the substrate is thermoplastic, should melt with some heat.
Anything else revealed at higher magnification?
Might be part of something like a micro-perforated bag (used for bread etc.)?? Not quite the same look, though.
It also seems that bits of plastic are showing up everywhere in nature. If the substrate is thermoplastic, should melt with some heat.
Anything else revealed at higher magnification?
Re: Man made?
I would place a magnet near it, to check the suspicion that it contains iron (and/or nickel).
Re: Man made?
Thanks PeteM and Hobbyst46.
Thought it might be, though I was hoping it would be something natural and therefore exotic.
I am afraid that was all I found. Did not think to keep the sample and have since washed the slide.
Total length was not much over 160µm so I would have struggled to run tests on it.
Will keep an eye out for larger pieces.
Thought it might be, though I was hoping it would be something natural and therefore exotic.
I am afraid that was all I found. Did not think to keep the sample and have since washed the slide.
Total length was not much over 160µm so I would have struggled to run tests on it.
Will keep an eye out for larger pieces.
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)
Re: Man made?
Hi together,
I think about which production process can lead to such a small holed pattern. Difficult to make a punch like this, injection moulding would be difficult too. Laser cutting, etching?
For a filter one would use a mesh or felt.
In electronics such fine (and much finer) shapes are used - separator of an electrolyte capacitor?
Bob
I think about which production process can lead to such a small holed pattern. Difficult to make a punch like this, injection moulding would be difficult too. Laser cutting, etching?
For a filter one would use a mesh or felt.
In electronics such fine (and much finer) shapes are used - separator of an electrolyte capacitor?
Bob
Re: Man made?
Bob - for some of the plastics, a process similar to calendaring can be used to make micro holes. Cheers, P.
Re: Man made?
Too many 'projects'
Re: Man made?
Compared to the forams and radiolaria that I have seen so far (very few, unforetunately) the mesh pattern on this dark piece of sample appears to be too uniform to be natural.
Re: Man made?
This one kind of takes us full circle; from diatoms to microporous battery anodes. Not likely the original found material, but still cool:
https://phys.org/news/2016-10-ancient-f ... cient.html
And yet another technique to replace lithographic substrates:
https://pubs.rsc.org/en/content/article ... ivAbstract
And then there's "biochar" - vaguely similar and possibly likely to be made in some industrial-scale process in the future:
https://biocharlie.com/blogs/news/70415 ... althy-soil
https://phys.org/news/2016-10-ancient-f ... cient.html
And yet another technique to replace lithographic substrates:
https://pubs.rsc.org/en/content/article ... ivAbstract
And then there's "biochar" - vaguely similar and possibly likely to be made in some industrial-scale process in the future:
https://biocharlie.com/blogs/news/70415 ... althy-soil
- Attachments
-
- fromancientf.jpg (7.49 KiB) Viewed 5447 times
Re: Man made?
Agree that it is probably not the one but yet it is the closest in regularity i.e. hole diameter and spacing, I would say.PeteM wrote:This one kind of takes us full circle; from diatoms to microporous battery anodes. Not likely the original found material, but still cool:
https://phys.org/news/2016-10-ancient-f ... cient.html
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)
Re: Man made?
Hi 75RR,
It could be the remains of an insect's compound eye. On the lower right corner of the object I imagine I can see lenses bulging from the holes.
Peter.
It could be the remains of an insect's compound eye. On the lower right corner of the object I imagine I can see lenses bulging from the holes.
Peter.
Re: Man made?
Thanks Peter
Having said that I found one that looks interesting (scroll down to red eye)
https://www.dreamstime.com/photos-image ... d-eye.html
I noticed that as well - tried to include it in the stack. However, the only close-up images of insect eyes that I have found seem to be hexagonal - though they are also remarkably regular in size and placing.It could be the remains of an insect's compound eye. On the lower right corner of the object I imagine I can see lenses bulging from the holes.
Having said that I found one that looks interesting (scroll down to red eye)
https://www.dreamstime.com/photos-image ... d-eye.html
- Attachments
-
- Screen-Shot.jpg (161.53 KiB) Viewed 5336 times
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)