Plancton net material comparison
Plancton net material comparison
Hi together,
I ordered some plancton net material from Aliexpress and compared it to my two existing nets when it arrived: https://www.aliexpress.com/store/group/ ... 235aP9wwv4
The nets are all made diferently, from diferent diameter material and differently woven. The fine Net from Aliexpress has double strands in one direction. this will limit the water flow to some degree, but make the net stronger and better to sew.
If one is the master of the sewing needle it would be a good idea to make the last 50mm of net before the beaker from fine mesh to reduce loss of fine plancton when it is washed into th beaker at the end of the pull. But this would make it more difficult to sew.
I often weld plastics in bigger diameters. It might be an idea to weld the nets, but it would be timme consuming to develop the right process for this.
Picture with a tiny peak measuring microscope, calibrated with an object micrometer.
Bob
Aliexpress 280 mesh 50µ
75 pixel x 130 pixel
36µ x 63µ
Aliexpress 100 mesh 150µ
400 pixel x 400 pixel
193µ x 193µ
Bob's big net
200 pixel x 200 pixel
96µ x 96µ
Bob's small Kosmos-Net
180 pixel x 180 pixel
87µ x 87µ
I ordered some plancton net material from Aliexpress and compared it to my two existing nets when it arrived: https://www.aliexpress.com/store/group/ ... 235aP9wwv4
The nets are all made diferently, from diferent diameter material and differently woven. The fine Net from Aliexpress has double strands in one direction. this will limit the water flow to some degree, but make the net stronger and better to sew.
If one is the master of the sewing needle it would be a good idea to make the last 50mm of net before the beaker from fine mesh to reduce loss of fine plancton when it is washed into th beaker at the end of the pull. But this would make it more difficult to sew.
I often weld plastics in bigger diameters. It might be an idea to weld the nets, but it would be timme consuming to develop the right process for this.
Picture with a tiny peak measuring microscope, calibrated with an object micrometer.
Bob
Aliexpress 280 mesh 50µ
75 pixel x 130 pixel
36µ x 63µ
Aliexpress 100 mesh 150µ
400 pixel x 400 pixel
193µ x 193µ
Bob's big net
200 pixel x 200 pixel
96µ x 96µ
Bob's small Kosmos-Net
180 pixel x 180 pixel
87µ x 87µ
- Attachments
-
- Aliexpress 280 50µ 1.jpg (186.55 KiB) Viewed 6315 times
-
- Aliexpress 100mesh 150µ 1.jpg (138.75 KiB) Viewed 6315 times
-
- Bobs Netz groß1.jpg (188.44 KiB) Viewed 6315 times
-
- Bobs Kosmos-Netz 90µ 1.jpg (156.15 KiB) Viewed 6315 times
Re: Plancton net material comparison
What an interesting comparison, Bob ... Thanks for sharing the photos
All are O.K.for the purpose, I guess; but they wouldn't make very good 'grading sieves'
MichaelG.
All are O.K.for the purpose, I guess; but they wouldn't make very good 'grading sieves'
MichaelG.
Too many 'projects'
Re: Plancton net material comparison
I have had some weight added to my plankton nets. Got the string that is used to pull long window/wall drapes down. It is sort of cloth tube, filled with small lead lumps. Three meters, that is ~100g, were added to each net. They were expertly sewn around the openings and along the net (see the thick white "strips").
The plastic neck of a large disposable soda bottle is "cuffed" within the small opening of the net (right side of the photo). The original plastic lid is piggybacked to the lid of a cheap plastic jar, volume ~100ml, on the right end of the net. The white stuff is Super-7 silicone adhesive that makes the piggyback.
Top net is a 120um hole size net (from the same Aliexpress), bottom net is 25um hole size net.
The efficiency of the added weight, and of the net itself, is still to be seen.
The plastic neck of a large disposable soda bottle is "cuffed" within the small opening of the net (right side of the photo). The original plastic lid is piggybacked to the lid of a cheap plastic jar, volume ~100ml, on the right end of the net. The white stuff is Super-7 silicone adhesive that makes the piggyback.
Top net is a 120um hole size net (from the same Aliexpress), bottom net is 25um hole size net.
The efficiency of the added weight, and of the net itself, is still to be seen.
- Attachments
-
- Untested plankton nets.jpg (109.68 KiB) Viewed 6304 times
Re: Plancton net material comparison
Hi Michael,
the middle two materials offer quite regular mesh sizes. I like stainless steel mesh better for sieves: Stronger, more precise, easy to weld to a ring and easy to clean.
These nets can probably cause trouble when you sample in sensitive environments since they tend to keep part of the catch in storage and transfer it from pond to pond. I think I will become a millionaire now with a plancton net fixative and deo combination! My two nets could use it for sure.
@Doron: Thank you for showing your nets - they look very expertly made!
How did you get along with the sewing? I work with lots of materials but am still uncomfortable with cloth and sewing.
The cone angle depends on the free mesh hole surface of the net (and the intended pull ing speed). For a coarse mesh the cone angle can be steeper.
The coarse mesh I ordered will probably be used for the filtration of our inflatable pool in the garden.
Bob
the middle two materials offer quite regular mesh sizes. I like stainless steel mesh better for sieves: Stronger, more precise, easy to weld to a ring and easy to clean.
These nets can probably cause trouble when you sample in sensitive environments since they tend to keep part of the catch in storage and transfer it from pond to pond. I think I will become a millionaire now with a plancton net fixative and deo combination! My two nets could use it for sure.
@Doron: Thank you for showing your nets - they look very expertly made!
How did you get along with the sewing? I work with lots of materials but am still uncomfortable with cloth and sewing.
The cone angle depends on the free mesh hole surface of the net (and the intended pull ing speed). For a coarse mesh the cone angle can be steeper.
The coarse mesh I ordered will probably be used for the filtration of our inflatable pool in the garden.
Bob
Re: Plancton net material comparison
Naturally, sewing was done by needle masters, not me...some sewing machine work, some hand sewing... like they did before everything was done by robots and software...
Re: Plancton net material comparison
Sorry ... Yes, I should have been more specificMicroBob wrote:Hi Michael,
the middle two materials offer quite regular mesh sizes.
Bob
MichaelG.
Too many 'projects'
Re: Plancton net material comparison
Update: the nets were pulled in seawater near the shore. They sank easily into the water and collected organisms as hoped.Hobbyst46 wrote:I have had some weight added to my plankton nets... ~100g were added to each net...
The efficiency of the added weight, and of the net itself, is still to be seen.
Warning: the yield can become foul-smelling within hours.
Re: Plancton net material comparison
I like your idea with the lead - tape. This solves the problem to apply weight in well spread manner to the sensitive mesh.
Re: Plancton net material comparison
Hi together,
for comparison I show here a picture of the stainless steel mesh I like to use. It is either 25µ or 50µ.
Compared to the plastic fibre net material it is more precisely woven and quite robust.
Bob
for comparison I show here a picture of the stainless steel mesh I like to use. It is either 25µ or 50µ.
Compared to the plastic fibre net material it is more precisely woven and quite robust.
Bob
- Attachments
-
- Edelstahlgitter Auflicht klein.jpg (484.11 KiB) Viewed 6182 times
Re: Plancton net material comparison
That does look robust. Useful not only in that it will doubtless last longer, but also in that it can be more thoroughly cleaned.
Would not think one would want old dead/decomposing matter mixed in with the new samples.
Would not think one would want old dead/decomposing matter mixed in with the new samples.
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)
Re: Plancton net material comparison
For a conical net the material is a bit expensive, but for filters made from plastic tubes and stainless mesh it is ideal. The mesh can simply be welded onto the tube with any piece of metal that has more than the melting temperature of the plastic. For plancton fishing one can just pour 20 beakers of water through the filter and then store the filter in the beaker, the bottle in the filter, and all together takes up little space in the backpack.