Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

Here you can discuss DIY adaptations to the microscope.
Post Reply
Message
Author
Scarodactyl
Posts: 979
Joined: Sat Mar 03, 2018 9:09 pm

Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

#1 Post by Scarodactyl » Thu Mar 28, 2019 2:06 am

I have an Olympus SZH (a very nice stereo scope), with a trinocular port. I found adapting a DSLR a bit difficult, as the 38mm external diameter dovetail isn't very standard. I did find a Diagnostic Instruments L clamp which fits on the dovetail, but this accessory is designed to pair with their own HR microscope camera adapters, and as such leaves no room for a normal-sized projection eyepiece that you'd need for a DSLR. The original adapter for DSLRs, the Olympus Photomicro L adapter, is still in much demand, since they're also used on the very popular BH series. They still command decent prices and aren't all that available on eBay. I saw one but got outbid (it ended at 127 bucks!), so I started thinking about alternatives.

The photomicro L adapter is just a physical adapter, the optics provided by a separate projective eyepiece that sits inside the dovetail (parfocal direct projection isn't possible). As such all I needed was a tube with an internal diameter of 38mm on one end, and able to accept a standard thread (like m42) on the other end. As it turns out 1.5 inches is 38.1 mm, and 1.5 inches is a standard diameter for PVC pipe. As such it's easy to get an adapter with flat ends and an ID of 1.5 inches. It's also very easy to get a 38mm tube to m42 adapter since this size is used for leica and nikon photo tubes. I happened to have all those components handy.

Image
So, all you need is a 1.5inch ID PVC adapter like this one (cost: around $2.50 or something), a 38mm to m42 adapter (around 20$), three set screws (~1$), an m42 spacer (~3 dollars) and an m42 helicoid (~16$), a bit of tape and the use of a drill. Total cost about 40 dollars, with potential room for cheaper substitutions.
The ID is a bit bigger than 38mm, so I put some strips of adhesive thermal printer paper until it could be press fit in firmly. That will hold it firmly but you can always retrieve the adapter later as well.
Image
Image
Drill three holes ~6mm from the bottom, and put the set screws in. I drilled them a bit small and put the set screws in by hand. A bit ugly, but functional. If you are more patient than me you could paint the PVC to match the color of the olympus scope and it might actually look pretty good too. The main reason I did not was painting PVC apparently requires some priming and long setting to be sure it's at maxiumum strength and I didn't want to wait before using it. I might make another one and swap the 38mm adapter over to it in the future.
Results are pretty positive.
Image
Image
(100% center crop)
Note that these photos were taken using a Nikon 2.5x projective eyepiece--this system was designed to use an Olympus NFK eyepiece, but they're more expensive. I'm honestly not 100% sure the NFK is the best choice anyway--it is a compensating eyepiece while the SZH uses non-compensating eyepieces, and I honestly doubt they add in abberations in the photo port to compensate. Either way the Nikon eyepiece does not seem to cause trouble.


Note that you could also just use this adapter here, but it doesn't come with a helicoid so it is still significantly mlre expensive than the DIY solution https://rover.ebay.com/rover/0/0/0?mpre ... 4215689212
You could also maybe get an mtv-5 without optics and swap out the c mount adapter for an m42 adapter, but that isn't a savings either.

Higgo
Posts: 2
Joined: Mon Jul 22, 2019 8:03 am

Re: Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

#2 Post by Higgo » Sun Aug 09, 2020 1:22 pm

You are an absolute legend. Thankyou very much for sharing this, you deserve more thanks :-)

Element 56
Posts: 271
Joined: Thu Oct 13, 2016 3:48 pm
Location: Lancaster County, PA

Re: Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

#3 Post by Element 56 » Mon Aug 10, 2020 12:47 am

Well done! A little ingenuity goes a long way!

I've been screwing around with an Olympus SZ40 and trying to get my Canon T7 set up. I have 1x diagnostic instruments adapter that's showing some promise. Still need to experiment a bit and workout the plumbing. Your PVC method may have opened some doors!
Thanks
Kirby

Scarodactyl
Posts: 979
Joined: Sat Mar 03, 2018 9:09 pm

Re: Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

#4 Post by Scarodactyl » Mon Aug 10, 2020 7:05 pm

This does work and has a certain............unique aesthetic, but I wouldn't recommend it. Better and cheaper to convert an Olympus PM unit: viewtopic.php?f=9&t=9093
Or a 3d printed solution would probably be the best of all.

Element 56
Posts: 271
Joined: Thu Oct 13, 2016 3:48 pm
Location: Lancaster County, PA

Re: Home made Olympus PhotoMicro Adapter L (38mm Dovetail) Replacement

#5 Post by Element 56 » Tue Aug 11, 2020 2:57 am

Scarodactyl wrote:
Mon Aug 10, 2020 7:05 pm
This does work and has a certain............unique aesthetic, but I wouldn't recommend it.
I like the PVC idea for a cheap inexpensive mockup. I seem to spend a lot of time messing with camera hight and different configurations. Once I have a combo that seems promising I like to work with it a while so I obviously I can't hold it by hand. The PVC opens up some quick alternatives to making aluminum parts on the lathe. I agree it's not a permanent solution but great for test and tune.
Kirby

Post Reply