First try at Fluorescence!

Here you can discuss different microscopic techniques and illumination methods, such as Brightfield, Darkfield, Phase Contrast, DIC, Oblique illumination, etc.
Post Reply
Message
Author
Gasman
Posts: 153
Joined: Sat Jan 09, 2016 1:36 pm
Location: North East UK

First try at Fluorescence!

#1 Post by Gasman » Fri May 07, 2021 9:41 pm

Hi guys
Very much a ‘101 in Fluorescence microscopy’ ;-).
3d printed this little holder which will have 3 bright blue led`s (only 1 at the moment) .
B700554B-1C30-4157-97F7-108C9E44730C.jpeg
B700554B-1C30-4157-97F7-108C9E44730C.jpeg (58.44 KiB) Viewed 4106 times
The plan was to use a blue light to excite a slide containing some cotton wool with a couple of strands which were stroked with a pink highlighter pen to hopefully show the strands fluorescing (is that actually a word?) when viewed through a yellow filter to bring out the pink strand.
406D07C2-A3F8-44A8-AA5C-377FDFAFBDF6.jpeg
406D07C2-A3F8-44A8-AA5C-377FDFAFBDF6.jpeg (71.65 KiB) Viewed 4106 times
No filter, you can barely make out the pink highlighted strand.


F3F975F6-19BE-4B30-B44A-0310C762E063.jpeg
F3F975F6-19BE-4B30-B44A-0310C762E063.jpeg (88.84 KiB) Viewed 4106 times
With yellow filter, much better. Its actually a printed yellow filter which ideally should filter out the blue light which it doesn`t really do so a proper one needed.

I think the concentration of blue light also needs to be increased which will hopefully be achieved when I fit the other two led`s.

best

Steve

crb5
Posts: 101
Joined: Sat Sep 12, 2020 11:55 pm

Re: First try at Fluorescence!

#2 Post by crb5 » Sat May 08, 2021 12:33 am

You might be better off sticking with a single LED and using a lens to focus excitation light on the sample. Light from multiple LEDs is difficult to combine into one bright illuminating spot. We used an LED flashlight with an extra lens. https://calcofi.org/downloads/Posters20 ... agshaw.pdf, https://www.youtube.com/watch?v=w1tG2wj_TAU and https://www.youtube.com/watch?v=BYvU9sOAuFM&t=28s

Gasman
Posts: 153
Joined: Sat Jan 09, 2016 1:36 pm
Location: North East UK

Re: First try at Fluorescence!

#3 Post by Gasman » Sat May 08, 2021 6:42 am

Yes thanks for that I did wonder about a focus lens. I was careful in designing the holder so all three leds should point to the same spot 🤞, will see how that works out 🤔
Steve

Hobbyst46
Posts: 4277
Joined: Mon Aug 21, 2017 9:02 pm

Re: First try at Fluorescence!

#4 Post by Hobbyst46 » Sat May 08, 2021 7:35 am

A long-pass interference filter will remove most of the blue background.

chrisimbee
Posts: 105
Joined: Fri Mar 19, 2021 5:34 pm

Re: First try at Fluorescence!

#5 Post by chrisimbee » Mon Jun 07, 2021 8:10 pm

this is really pretty good for a first but I think you should try a filter of a bit deeper yellow to get rid of most of blue light and enhance the fluorescence.

Try with some moss or pond alguae as they fluoresce in bright red :)
microscope Olympus BH2-BHTU+epifluo RFC @ 470 nm
Zeiss neofluar x16Ph, x40Ph, x100 oilPh
LOMO Ph x10 X20 X40 X90oil
Olympus SPFl x2
Olympus SPx20, SPx40 SPx100
camera astro ZWO ASI 120MM (n&b) et ZWO ASI 120 MC (colour)
Nikon D3100

Gasman
Posts: 153
Joined: Sat Jan 09, 2016 1:36 pm
Location: North East UK

Re: First try at Fluorescence!

#6 Post by Gasman » Mon Jun 07, 2021 10:26 pm

Thanks for that Chris, I’ll give that a try!.
Steve

Rat
Posts: 9
Joined: Fri Jun 25, 2021 6:02 pm

Re: First try at Fluorescence!

#7 Post by Rat » Wed Aug 18, 2021 5:57 pm

Otra opción sería colocando un filtro BG -12 (azul verde) frente a la luz (no se requiere filtro amarillo). Por supuesto, los filtros cuestan más que su configuración, pero se pueden usar con cualquier luz de flash brillante para ver la fluorescencia con un estereoscopio y no se necesita un filtro amarillo. Otras luces ultravioletas también funcionan y se utilizan para ver líquenes, rocas, etc.

https://es.aliexpress.com/item/32889032226.html

https://canadiannaturephotographer.com/ ... scopy.html

crb5
Posts: 101
Joined: Sat Sep 12, 2020 11:55 pm

Re: First try at Fluorescence!

#8 Post by crb5 » Wed Aug 18, 2021 6:19 pm

y no se necesita un filtro amarillo
=
and no yellow filter is needed
You would still need a yellow filter in the emission path as the reflected/scattered light from the BG12 filter would be much more intense than the fluorescence emission from most samples. If a cheap yellow filter is insufficient to block, try a cheap orange filter - or obtain a better quality yellow filter (i.e. sharper cut off and high OD in the blue region).

Post Reply