Overhead lighting for compound scope (T720Q)
Overhead lighting for compound scope (T720Q)
I have an Amscope T720Q. Sometimes I'd like to examine non-transparent objects, and I don't want to stretch to a dedicated stereo scope yet. Is there a best practice way to do this, such as an appropriate ring light adapter or goosenecks?
Is there a specific solution that others have tried on such Amscopes that works well? Is there even a ringlight that could actually work (single objective lens only I guess), or it must be goosenecks?
Is there a specific solution that others have tried on such Amscopes that works well? Is there even a ringlight that could actually work (single objective lens only I guess), or it must be goosenecks?
-
- Posts: 1186
- Joined: Tue Oct 20, 2020 6:44 am
Re: Overhead lighting for compound scope (T720Q)
I think it depends upon the objectives used. A gooseneck will do the job for 4, 10, and 20x. Above that in my experience you will be lucky to get anything to work due to lack of space between the objective and the specimen. I've heard of perfectly aiming a laser pen light at the edge of the slide for oblique lighting but I've never tried it..
Greg
Greg
Re: Overhead lighting for compound scope (T720Q)
Hi, for the lower powers one or two IKEA Jansjö lamps do a good job. To even out illumination a table tennis ball an be cut in half and a hold for the objective can be added.
Bob
Bob
-
- Posts: 1186
- Joined: Tue Oct 20, 2020 6:44 am
Re: Overhead lighting for compound scope (T720Q)
That's an interesting comment. The half ball would act as a parabolic to focus the light. Sounds cool.
Greg
Greg
Re: Overhead lighting for compound scope (T720Q)
Use scissors as much as you can when cutting the ping pong ball --or they will turn blood red.
Re: Overhead lighting for compound scope (T720Q)
.Greg Howald wrote: ↑Sun Jun 06, 2021 11:47 amThat's an interesting comment. The half ball would act as a parabolic to focus the light. Sounds cool.
Greg
Well actually, no ... a hemispherical surface makes a rather poor job of focusing
MichaelG.
.
https://en.wikipedia.org/wiki/Parabolic_reflector
https://youtu.be/djkBahaEHG4
Too many 'projects'
Re: Overhead lighting for compound scope (T720Q)
.
This is an example of a ping-pong ball in use:
https://www.microbehunter.com/microscop ... 145#p29145
This is an example of a ping-pong ball in use:
https://www.microbehunter.com/microscop ... 145#p29145
Zeiss Standard WL (somewhat fashion challenged) & Wild M8
Olympus E-P2 (Micro Four Thirds Camera)
Olympus E-P2 (Micro Four Thirds Camera)
Re: Overhead lighting for compound scope (T720Q)
Half of half ping-pong balls are sometimes easier to get into position 'after the event'
[That is a bit of a wooden skewer attached with holt-melt on the right hand side one]
[That is a bit of a wooden skewer attached with holt-melt on the right hand side one]
Re: Overhead lighting for compound scope (T720Q)
.... and if you are trying to photograph discreet unmounted things eg small dead insects, you could try putting them into the bottom of a half-ping-pong ball ... this can be rested on a microscope-slide sized piece of plastic or cardboard with a round hole cut into the middle and lit from the side
(with a jansjo light ..sadly, no longer available): this gives quite a reasonably softish lighting:
The ping pong balls are really just to soften the lighting and so avoid really bright reflections that come directly from the light source
The back plastic slide used in the photo to hold the ball was actually a microscope watch-glass holder that was being made and sold on eBay by a 3D printing person. I have just looked, but I dont see them for sale any more.
(with a jansjo light ..sadly, no longer available): this gives quite a reasonably softish lighting:
The ping pong balls are really just to soften the lighting and so avoid really bright reflections that come directly from the light source
The back plastic slide used in the photo to hold the ball was actually a microscope watch-glass holder that was being made and sold on eBay by a 3D printing person. I have just looked, but I dont see them for sale any more.
-
- Posts: 1186
- Joined: Tue Oct 20, 2020 6:44 am
Re: Overhead lighting for compound scope (T720Q)
That's a really good result. I'll have to try it. I really like such experimentation.
Greg
Greg
-
- Posts: 3354
- Joined: Sun Mar 22, 2020 10:06 am
- Location: Winnipeg, Manitoba, Canada
Re: Overhead lighting for compound scope (T720Q)
I use 2 focused flashlights mounted on stands to direct beams virtually parallel to the stage at the subject. This lighting improves shadows and builds the topology of the subject using the 60x objective.
Re: Overhead lighting for compound scope (T720Q)
Thank you everyone for your kind replies - great ideas!
- iconoclastica
- Posts: 182
- Joined: Sun Jan 20, 2019 5:43 pm
Re: Overhead lighting for compound scope (T720Q)
Wouldn't you rather mix in some transmitted light so the background turns white, instead of inside-of-pp-ball-coloured?